Trailer Hire in Perth: The Towing Rules and Checks That Matter

trailer hire Perth

If you are towing a trailer anywhere in Western Australia, the single most important thing to know is that you are capped at 100 km/h, even on roads posted at 110. That limit comes from the Road Traffic Code 2000 and it is not signposted anywhere. It applies no matter how light the trailer is. Plenty of people who have towed for years in other states do not know this, and it is the most common way an otherwise careful driver picks up a fine on a WA highway.

The rest of the rules are less surprising but no less important. This guide covers what the law requires of you when you tow in WA, what to check before you leave, and how to load a trailer so it behaves itself at speed. It is written for people hiring a trailer rather than owning one, so it assumes you have not towed recently and are not familiar with the specific unit.

How fast can you tow in Western Australia?

100 km/h. That is the maximum, full stop.

The Road Traffic Code 2000 provides that a person must not drive a vehicle to which a trailer or other vehicle is attached at a speed exceeding 100 km/h. Main Roads Western Australia lists this among the statutory speed limits, which are the limits that apply by regulation rather than by sign. The Code expects you to know them as a condition of holding a licence.

Three consequences worth being clear about:

  • It applies regardless of trailer weight. A small box trailer with a bicycle in it is subject to the same 100 km/h cap as a loaded tandem.
  • It overrides the posted limit where the posted limit is higher. On a 110 zone heading north on the Brand Highway, you are still limited to 100.
  • Where the posted limit is lower, the posted limit wins. The statutory limit is a ceiling, not a licence.

Your vehicle’s manufacturer may also specify a lower towing speed for that model, particularly at higher trailer weights. Where the manufacturer specifies a lower figure, that is the one to work to.

Why this catches people out. Most states set the towing speed at the posted limit, or apply a reduced limit only above a combined mass threshold. Western Australia applies a flat 100 km/h to every towing combination. If you have towed interstate and are applying that experience here, you are probably applying the wrong rule.

Does the trailer need brakes?

It depends on the gross trailer mass, and the thresholds are set out clearly in the Department of Transport’s safe towing guidance.

Gross trailer mass Braking requirement
Single axle, not over 750 kg Brakes not required
Over 750 kg Brakes required
Over 750 kg and not over 2,000 kg Braking on the wheels of at least one axle. Over-ride brakes are permitted
Over 2,000 kg Braking on all wheels, operated from the driver’s seated position. Over-ride brakes are not permitted

 

There is a companion rule that matters just as much and is easier to miss. If a trailer is not fitted with brakes, its loaded mass must not exceed 750 kg. That is a limit on what you can put in it, not just on what the trailer weighs empty. A light unbraked trailer loaded with pavers can exceed 750 kg without looking full.

This is one reason a braked tandem trailer is a more forgiving thing to hire than an unbraked box trailer. Burswood Car Rentals hires braked tandem trailers, which removes the 750 kg loaded mass ceiling from the equation and gives you braking that works with the tow vehicle rather than relying on it entirely.

What about safety chains?

Safety chains are mandatory. Their job is to keep the trailer attached to the vehicle if the coupling releases, which is a rare event with an enormous consequence.

The Department of Transport’s Safe Towing Guide sets the requirement by aggregate trailer mass:

  • Under 2,500 kg aggregate trailer mass: at least one safety chain.
  • Between 2,500 kg and 3,500 kg: two safety chains.

Chains must meet the applicable Australian Standard. For trailers up to 3,500 kg aggregate trailer mass, Australian Design Rule 62/02 requires compliance with AS 4177, the standard covering caravan and light trailer towing components. Complying chain carries a marking repeated along its length, which is how an inspector tells rated chain from hardware store chain.

In practice, on a hire trailer, the chains will already be correct. What you need to get right is how you connect them. Cross the chains under the drawbar so that if the coupling lets go, the drawbar lands in the cradle the chains form rather than digging into the road. Leave enough slack to turn, but not so much that the drawbar can reach the ground.

Is the tow vehicle up to the job?

Two numbers matter and they are not the same number.

The towbar and coupling capacity must be at least equal to the loaded mass of the trailer. On a vehicle built after January 1992, the towbar must be marked with its load capacity along with either the vehicle model it was designed for or the manufacturer’s part number. If you are looking at an unmarked towbar on a modern vehicle, that is a problem.

The vehicle’s towing capacity is set by its manufacturer and is often quoted as two separate figures, one for a braked trailer and one for an unbraked trailer. The braked figure is usually much higher.

Where a vehicle was built before 1 January 1992 and the manufacturer never specified a maximum towing capacity, the fallback guidance is 1.5 times the unloaded mass of the vehicle for a trailer fitted with appropriate brakes, and a maximum of 750 kg for a trailer without brakes. This is rarely relevant to a hire vehicle but it comes up with older private tow vehicles.

The loaded mass of the trailer must never exceed the trailer’s aggregate trailer mass, which is the maximum the trailer itself is rated to weigh when loaded. If you are unsure what your combination actually weighs, a public weighbridge will tell you in a few minutes.

How do you load a trailer so it tows properly?

Trailer sway is almost always a loading problem rather than a driving problem. Get the loading right and most of the difficulty disappears.

Put weight forward of the axle

The heaviest items go slightly forward of the trailer’s axle, low down and centred. This puts a modest downward load on the towball, which is what keeps the trailer tracking behind you. A trailer loaded heavy at the back will lift the ball, unload the tow vehicle’s rear wheels and start to sway.

Balance side to side

A load stacked against one side pulls the trailer out of line and loads one tyre far more than the other. Spread it.

Restrain everything

In Western Australia, load restraint on all vehicles is governed by the Road Traffic (Vehicles) Regulations 2014, which reference the Load Restraint Guide 2004, Second Edition. This is a genuine difference from most of the country. Queensland, New South Wales, Victoria, Tasmania, South Australia and the ACT reference the 2018 light vehicle guide instead. The National Transport Commission has noted there is no material practical difference between the performance standards in the two editions, but the version with legal standing in WA is the 2004 guide.

The headline standard is that the restraint must withstand 0.8 times the mass of the load in the forward direction, which is what hard braking generates. Use rated straps and ratchet tie downs rather than rope, use a net or tarp over anything that could lift out, and check the load again after the first twenty minutes of driving.

Do not fill it just because it is empty

Volume is not the constraint. Mass is. A tandem trailer will physically hold more sand than you are allowed to carry in it.

The pre-departure check

Five minutes before you leave, every time. Most towing incidents trace back to something on this list.

  1. Coupling seated and locked. Latch fully engaged, locking pin or clip in place. Lift the drawbar to confirm it will not come off the ball.
  2. Safety chains crossed and connected to rated attachment points, with enough slack to turn and not enough to touch the road.
  3. Lights working. Indicators, brake lights, tail lights and number plate light. Have someone stand behind while you cycle through them. Trailer lights must operate in unison with the vehicle’s.
  4. Electrical plug seated and the lead routed so it cannot drag or stretch on a tight turn.
  5. Pressure and condition on the trailer and the tow vehicle. Trailer tyres often sit for long periods and lose pressure. Do not forget the spare.
  6. Jockey wheel raised and locked clear of the road.
  7. Load restrained and, if applicable, the tarp or net secured at every edge.
  8. If the trailer is wider than the tow vehicle, you need to be able to see past it. Extension mirrors may be required.
  9. Brake controller set if the trailer has electric brakes.

Driving with a trailer behind you

The vehicle you are driving is now considerably longer and heavier, and it responds differently to everything.

  • Braking distance increases. Leave much more room than feels necessary, particularly on a wet Kwinana Freeway.
  • Keep back from heavy vehicles. When towing in WA you must stay at least 60 metres behind a heavy vehicle or another towing vehicle, unless you are overtaking.
  • Take corners wider. The trailer cuts inside your line. Roundabouts and kerbside turns in the older inner suburbs are where trailers meet kerbs.
  • Overtake with far more room than you would normally use, and think carefully about whether you need to at all.
  • Avoid sudden steering inputs. Sway is usually triggered by a quick correction. If it starts, ease off the accelerator, keep the steering straight and let it settle rather than braking hard.
  • Reversing takes practice. Small steering inputs, and an observer outside the vehicle is genuinely helpful. Find an empty carpark and try it once before you need to do it in a driveway.

What are people usually hiring a trailer for in Perth?

Four jobs account for most trailer hires, and each one has a different answer to the question of what else you need.

Moving house

The most common reason and the one where a trailer changes the day most. A trailer behind an SUV or a ute turns a repeated shuttle into one or two runs. If you are moving a full household, hiring the tow vehicle and the trailer together from the same supplier means the combination is matched and approved, and you are not trying to fit a hired trailer to a car that was never set up to tow.

Tip and green waste runs

Perth’s transfer stations are built for trailers. Watch the loaded mass rather than the volume, particularly with soil, sand and wet green waste, which are all much heavier than they look.

Renovation and garden projects

Pavers, sleepers, mulch, demolition waste. This is the category where the 750 kg unbraked limit bites hardest, and where a braked tandem is worth the difference.

Taking gear away for a trip

Camping equipment, bikes, boards, fishing gear. Bulky rather than heavy, so mass is rarely the constraint. What matters here is that everything is covered and restrained, because this is the load type most likely to lift out at speed.

Practical notes for hiring a trailer in Perth

  • Check your vehicle is actually set up to tow before you book the trailer. A towbar is not standard on every vehicle and an electrical connection is not always fitted even where a towbar is.
  • If you are hiring the tow vehicle too, book both together. It removes the question of whether the combination is approved.
  • Photograph the trailer before you leave. Chassis, tyres, lights, coupling, and the interior of the tray.
  • Practise the reverse once. Five minutes in an empty carpark is worth an hour of frustration later.
  • Plan your parking. A tow vehicle and trailer will not fit in a standard bay, and many Perth shopping centre carparks have height and length restrictions.
  • The Burswood depot is at 16 Teddington Road, on the airport to city route, which makes collection straightforward from most directions.

Common questions

Can a learner driver tow a trailer in WA?

Under WA licensing rules, a learner may tow while accompanied by an experienced driver. This differs from several other states, where learner drivers cannot tow at all. Hire agreements set their own driver requirements though, and these are usually stricter than the licensing rules, so confirm before booking.

Do I need a special licence to tow?

For a light trailer behind a standard vehicle, no. A C class licence covers it, provided the combination stays within the rated limits of the vehicle, the towbar and the trailer.

Can anyone ride in the trailer?

No. Never, under any circumstances.

What if a light stops working on the way?

You cannot legally continue with a trailer whose lights are not operating. Most failures are the plug working loose rather than a bulb, so check the connection first.

Booking a trailer

Work out the mass of what you are moving before you choose the trailer, not after. If the load is heavy, a braked tandem is the right unit. If you also need the tow vehicle, book both on the same reservation so the combination is matched.

The Instant Quote on the Burswood Car Rentals site will show availability for trailers and tow vehicles together. If you are not sure whether your own vehicle is suitable, call (08) 9362 4777 or send a message on WhatsApp to 0438 757 909 and describe the vehicle and the load.

Ute Hire in Perth: Which Jobs Actually Need One

ute hire Perth

If you are moving a fridge, taking green waste to the tip, picking up flat pack furniture or running tools to a job site, a ute is the right vehicle. If you are moving a whole household, a ute on its own will cost you more trips than it saves, and a ute towing a trailer is usually the better answer. That is the short version, and for most Perth jobs it is the whole answer.

The longer version matters because hiring the wrong vehicle is expensive in a way that does not show up on the invoice. It shows up in the third trip back to Osborne Park, in the couch that did not fit, and in the load that shifted on the Graham Farmer Freeway. This guide covers what a ute is genuinely good for in Perth, what Western Australian law requires of you once something is in the tray, and how to work out whether you need the ute, the trailer, or both.

What is a hire ute actually good for?

A ute earns its keep when the load is heavy, dirty, awkwardly shaped or all three. The open tray is the point. You are not trying to angle a wardrobe through a door aperture or worrying about what a bag of garden soil is doing to the boot carpet.

The jobs a ute handles better than anything else in a hire fleet:

  • Tip runs. Green waste, renovation offcuts, an old mattress. Perth’s transfer stations are set up for utes and trailers, and an open tray is far quicker to unload than a boot.
  • Building and landscaping supplies. Bagged soil, pavers, timber lengths, plasterboard sheets. Bunnings and the trade suppliers along Great Eastern Highway load straight into a tray.
  • Single large items. A fridge, a washing machine, a bed base, a ride on mower. One item, one trip, no disassembly.
  • Tools and trade gear. If you are working across sites for a week and need everything with you, a dual cab gives you a locked cabin for the valuable gear and a tray for the rest.
  • Anything wet, sandy or muddy. Boat gear after a morning at Hillarys, camping equipment coming back from Lancelin, surfboards and wetsuits. A tray hoses out.

The jobs a ute handles badly are the ones people most often hire one for. A full house move is the main offender. A tray holds a lot less than it looks like it does once boxes are stacked to a height that can actually be strapped down, and every load is exposed to weather and to the road.

Do you need a ute, a trailer, or both?

This is the question that decides the booking, and it is worth two minutes of thought before you book anything.

A ute on its own

Right when the load is heavy for its size and you want to load and unload quickly. Soil, sand, pavers, appliances, tools. A ute is also easier to park and reverse than any towing combination, which matters if the job is in Northbridge or somewhere in the western suburbs with a narrow verge.

A car or SUV towing a trailer

Right when the load is bulky rather than dense, and when you also need to carry passengers in comfort. A trailer gives you volume. It is also the better answer for a single awkward item that will not fit in a tray, like a long ladder or a canoe.

A ute towing a trailer

Right for a genuine house move or a big clean out. This is the combination that turns a three trip job into a one trip job. Burswood Car Rentals hires braked tandem trailers alongside its Toyota Hilux utes, so both halves of the combination can come from the same booking and you are not coordinating two suppliers on the same morning.

Worth knowing before you commit to towing. In Western Australia the Road Traffic Code 2000 sets a statutory maximum of 100 km/h for any vehicle towing a trailer, regardless of what the trailer weighs and regardless of the posted limit on the road. It is not signposted. If your run includes a stretch of highway zoned at 110, you are still capped at 100 the moment a trailer is on the back.

What licence do you need for a hire ute in WA?

A standard C class licence is enough. It covers vehicles up to 4.5 tonnes gross vehicle mass, which takes in the single cab and dual cab utes that make up a hire fleet. You do not need a light rigid licence or any endorsement.

Towing does not change the licence class either, provided the combination stays within the limits of the tow vehicle and the trailer. What it does change is how the vehicle behaves, which is a separate problem and one that catches out drivers who have never towed.

If you hold an overseas licence, the licence itself is generally not the obstacle. The hire company’s own requirements are. Confirm those when you book rather than at the counter.

How do WA load restraint rules work?

This is the part most guides get wrong, and it is worth getting right because Western Australia is genuinely different from the eastern states.

The Road Traffic (Vehicles) Regulations 2014 reference the Load Restraint Guide 2004, Second Edition. Queensland, New South Wales, Victoria, Tasmania, South Australia and the ACT moved to the Load Restraint Guide for Light Vehicles 2018. Western Australia and the Northern Territory did not. The National Transport Commission has said there is no material practical difference between the performance standards in the two editions, but the version with legal standing in WA is the 2004 guide.

What that means for you in the tray of a ute is straightforward. Your restraint has to be strong enough that the load does not move under the forces of normal driving. The headline performance standard is that the restraint must withstand 0.8 times the mass of the load in the forward direction, which is the force generated by hard braking. The guide sets lower standards for rearward, sideways and vertical movement. In plain terms, the forward direction is the one that will catch you out, because braking is where a load wants to go through the back of the cab.

The guide is guidance, not prescription. You can restrain a load any way you like as long as you can demonstrate it meets those performance standards.

What that looks like in practice

  • Use rated straps and ratchet tie downs, not rope. The Department of Transport is explicit about this. Rope stretches, loosens and is almost impossible to tension properly.
  • Use the rated anchor points. Check them for damage before you load. An anchor point that has been bent is not rated any more.
  • Cover loose material with a net or tarp. Anything that can lift out in airflow needs to be contained, not just held down. Bagged mulch at 100 km/h behaves differently to bagged mulch in a driveway.
  • Load heavy items forward and low, over or ahead of the rear axle, and spread the weight evenly across the tray rather than to one side.
  • Tie down at an angle, not straight across a tall load. A strap running flat over the top of a high load does very little to stop it sliding forward.
  • Check the load during the trip. Anything that can settle will settle, and a strap that was tight in the driveway can be slack twenty minutes later.

If you are putting a ladder or long timber on a roof rack rather than in the tray, the same principle applies and there is a weight limit on the rack itself. The Department of Transport publishes a bulletin specifically on tradespeople’s roof racks.

What can go wrong, and how to avoid it

Overhanging loads

Timber, pipe and ladders routinely overhang the back of a tray. There are limits on how far a load may project and requirements for marking an overhanging load so it is visible to other drivers. If your load is going to hang out the back, plan for it before you load rather than improvising at the supplier.

The load that fits but should not travel

A load can be within the tray and still be unsafe. Loose bricks stacked without restraint, an unsecured toolbox, a gas bottle rolling around. If it can move, it will, and a hard stop on Orrong Road is enough to prove it.

Passengers in the tray

Not permitted, in any circumstances, and prohibited by any hire agreement you will sign. Everyone travels in a seat with a restraint.

Assuming a dual cab has the same tray as a single cab

It does not. A dual cab trades tray length for a second row of seats. If your load is long and you also need to carry three passengers, that is the trade off to think about before you book, and it is often the point at which a trailer starts to make sense.

Single cab or dual cab?

The choice comes down to whether you are moving people or moving things.

A single cab gives you the longer tray. If the job is genuinely a load carrying job and there are one or two of you, this is the more useful vehicle. Long items sit inside the tray rather than hanging over the tailgate.

A dual cab gives you a back seat and a shorter tray. It is the right call when the crew travels together, when you want a lockable cabin for tools and laptops, or when the ute is doing double duty as a work vehicle during the week and a family vehicle on the weekend. Most people hiring a ute for a few days want the dual cab, and most people hiring one for a specific heavy job want the single cab.

Hiring a ute for trade use

Trade hire is a different problem to a weekend tip run, and it is worth treating it as one.

The usual driver is capacity rather than replacement. A business with its own vehicles hits a fortnight where there is one more job than there are utes, or a vehicle goes in for repair in the middle of a run. Hiring to cover that gap is cheaper and faster than buying, and it does not commit the business to an asset it only needs for three weeks a year.

Three things make trade hire work better than ad hoc hire:

  • Set up an account rather than booking each time. A corporate or trade account removes the payment step from every individual hire and puts the invoicing on terms your bookkeeper can work with. Burswood Car Rentals offers corporate accounts.
  • Book the vehicle class, not the exact model. Availability is easier to secure and you are unlikely to care whether the tray sits on one badge or another as long as it does the job.
  • Nominate your drivers properly. Everyone who will drive the vehicle needs to be on the agreement. An unlisted driver is the fastest way to turn a small incident into an uninsured one.

If the vehicle is going to be branded, carrying signage or fitted with anything, ask before you book. Adhesive signage and drilled fittings are almost always outside a standard hire agreement, and it is much easier to find that out beforehand than to explain it at the return.

How long should you book a ute for?

Longer than you think, and this is not upselling. Two patterns account for most of the stress people report on a ute hire.

The first is the half day booking for a job that turns out to need a second trip. Tip runs are the classic case. What looked like one load in the backyard becomes two once it is actually stacked and strapped.

The second is the weekend move that runs into Monday morning. Loading takes longer than expected, the new place is not ready, someone is late. A booking with a day of margin in it costs less than a rushed return and a job half finished.

For trade use across multiple sites, weekly and longer hires generally work out better per day than repeated short hires, and they remove the daily pick up and drop off from your schedule entirely.

Practical notes for hiring a ute in Perth

  • The depot sits on the airport to city route. Burswood Car Rentals operates from 16 Teddington Road, Burswood, which is convenient if you are collecting on the way in from Perth Airport or heading out towards the eastern suburbs.
  • Delivery is available to Perth city hotels and Crown within 20 kilometres, which is useful if you are working in the CBD and do not want to make the trip to the depot to collect.
  • Take photographs before you drive off. Tray, tailgate, anchor points, tyres, and any existing marks. It takes two minutes and it settles any question later.
  • Bring your own straps if you have preferred gear. Check what the vehicle comes with when you book rather than assuming.
  • Think about where you will park it. A ute is longer than the sedan you normally drive, and a tandem trailer behind it is considerably longer again. Residential streets in the older inner suburbs are tight.

Common questions

Can I take a hire ute on unsealed roads?

This depends entirely on the hire agreement, and the answer varies between companies and between vehicle types. It is one of the most common causes of a dispute after a hire, so confirm it before you book if your plans involve gravel.

Do I need to return it clean?

Return conditions vary. If you have been carrying soil, sand or green waste, a quick hose out of the tray before you return it is sensible regardless of what the agreement says.

Can I tow with a hire ute?

Where the vehicle is set up for it and the hire agreement permits it, yes. Booking the ute and the trailer together from the same supplier is the simplest way to make sure the combination is matched and approved.

What if the load will not fit?

Ring before you book rather than after. Describing the actual load to someone who knows the fleet is faster than guessing from a website, and it is the difference between one trip and three.

Getting a ute booked

Work out the load first, then the vehicle. If it is heavy and compact, a ute. If it is bulky and light, a trailer. If it is a house, both. Once you know which, the Instant Quote on the Burswood Car Rentals site will give you availability and a rate in a few steps, and you can add a trailer to the same booking.

If you are not sure which combination suits the job, describe the load over the phone on (08) 9362 4777 or by WhatsApp on 0438 757 909. It is a two minute conversation that saves an afternoon.

Best Beaches Near Perth Reachable by Hire Car

Perth is blessed with one of the finest urban beach coastlines in the world, with pristine white sand and Indian Ocean water stretching north and south of the city for hundreds of kilometres. The difference between having a hire car and relying on public transport is the ability to reach the quieter, less crowded beaches beyond the main city beaches, to stop when something looks good, and to explore the coast at your own pace.

Burswood Car Rentals has been helping Perth visitors discover Western Australia for over 42 years. Hire a car from Burswood and take your pick of the Perth coast.

Hire a Car and Hit the Beach

Burswood Car Rentals: from $25/day, no hidden fees, near Perth Airport. Call (08) 9362 4777.

Get a Quote

The City Beaches (10 to 15 km from Perth CBD)

Cottesloe Beach

Cottesloe is Perth’s most iconic and photographed beach. Norfolk Island pines frame the foreshore, the historic Indiana Tea House overlooks the water, and the beach is well-serviced with facilities, cafes, and a good surf break. Ocean swimming conditions are generally calm and family-friendly. Cottesloe hosts the Sculpture by the Sea exhibition every March.

City Beach

City Beach is a broad, open beach approximately 10km from the CBD, popular with families for its excellent facilities including a large playground, kiosk, cafe, and ample parking. Conditions are good for swimming and the beach is less crowded than Cottesloe on most days.

Scarborough Beach

Scarborough, approximately 14km from the CBD, is Perth’s main surf beach, with consistent Indian Ocean swells that attract beginner to intermediate surfers. The Scarborough foreshore has been significantly redeveloped in recent years, with a new amphitheatre, restaurants, bars, and a water playground. It has a livelier atmosphere than the more sedate city beaches.

North of Perth (20 to 60 km)

Trigg Beach and Mettams Pool

Trigg Beach, just north of Scarborough, offers a quieter alternative to the main surf beach, with a rocky reef break popular with experienced surfers and a small sheltered area at Mettams Pool that is excellent for snorkelling in calm conditions. The natural reef just offshore creates a protected swimming area.

Sorrento and Mullaloo

Continuing north along the coast, Sorrento and Mullaloo beaches offer suburban beach atmosphere without the tourist crowds. Both have good facilities, a beachfront cafe or kiosk, and consistent swimming conditions. Sorrento is adjacent to Hillarys Boat Harbour, which has a marina, restaurants, and the departure point for the Rottnest Island ferry.

Yanchep Beach

Approximately 56 kilometres north of Perth, Yanchep and the nearby Two Rocks area offer beaches with a significantly quieter atmosphere than the city beaches. The drive north along Marmion Avenue and then the Mitchell Freeway extension is straightforward. Yanchep National Park is adjacent and has a population of western grey kangaroos and a cave system, making it worth a combined beach and park day trip.

South of Perth (20 to 40 km)

Rockingham Beaches

Rockingham, approximately 47km south of Perth via the Kwinana Freeway, offers calmer swimming conditions than the open ocean beaches north of the city, as parts of the Rockingham coastline are sheltered by nearby islands. Point Peron and the Palm Beach area offer white sand and clear water in a more sheltered environment. Rockingham is also the departure point for tours to Penguin Island, where a colony of little penguins can be observed.

Mandurah

At approximately 72km south of Perth, Mandurah is at the outer edge of a day trip but is worth including in a longer coastal drive south. The Mandurah Estuary and the beaches along the Dawesville Channel offer a different coastal experience to the Indian Ocean beaches, with calm, warm estuary water popular with families.

Beach Distance from Perth Character Best for
Cottesloe ~12km Iconic, heritage foreshore, calm water First-time visitors, families, photography
City Beach ~10km Broad, well-facilitated, family-friendly Families, swimming
Scarborough ~14km Lively, surf beach, redeveloped foreshore Surf, dining, younger visitors
Trigg/Mettams Pool ~17km Quieter reef beach, snorkelling Snorkelling, experienced surfers
Sorrento/Mullaloo ~24km Suburban, uncrowded Quiet swim, locals atmosphere
Yanchep ~56km Remote feel, adjacent national park Half-day trip, wildlife
Rockingham ~47km Sheltered, penguins nearby Families, calm swimming

Frequently Asked Questions

Which Perth beach is best for young children?

City Beach and Rockingham both offer calm, well-supervised swimming conditions with excellent facilities that suit young children. Mettams Pool at Trigg is also excellent for children as the reef creates a partially sheltered, shallow lagoon with calmer water than the open ocean beach.

Are there beach parking fees in Perth?

Most Perth beach carparks are free, which makes exploring the coast by hire car very accessible. Some popular areas like Cottesloe and Scarborough have a mix of free and paid parking, with free options within a short walking distance. Burswood Car Rentals’ hire cars carry no rental stickers, so you blend in with locals at all parking areas.

Perth to Rottnest Island: Can You Take a Hire Car?

Rottnest Island is one of Western Australia’s most popular destinations, famous for its quokkas, clear turquoise water, historic buildings, and car-free atmosphere. That last point is the key one for hire car visitors: Rottnest Island does not permit private vehicles on the island. You cannot take your hire car to Rottnest, regardless of which ferry service you use. But your hire car still plays an important role in making the trip happen.

Burswood Car Rentals has been helping Perth visitors explore Western Australia for over 42 years. This guide explains the Rottnest logistics clearly so you can plan your trip with confidence. Browse our Perth hire car options for a vehicle that suits your itinerary.

Hire a Car to Get to the Rottnest Ferry

Burswood Car Rentals: no hidden fees, near Perth Airport, from $25/day. Call (08) 9362 4777.

Get a Quote

Why There Are No Cars on Rottnest Island

Rottnest Island has been car-free for private vehicles since the 1930s. This policy is managed by the Rottnest Island Authority under the Rottnest Island Authority Act 1987. The only motor vehicles operating on the island are managed by the Rottnest Island Authority for essential services, emergency response, accommodation, and specific tourism operations. No private vehicles, hire cars, or passenger vehicles are permitted on the ferry services for general visitor access.

This policy is central to the island’s appeal: the absence of traffic noise and the ability to cycle freely around the island is a defining feature of the Rottnest experience.

How Your Hire Car Gets You to Rottnest

While your hire car cannot cross the water to Rottnest, it plays an important role in getting you to the ferry terminal. There are three main ferry departure points for Rottnest Island from the Perth area:

Ferry terminal Distance from Perth CBD Drive time Notes
Barrack Street Jetty, Perth City centre Walk / city parking Most central; good if you are staying in the CBD
Fremantle Passenger Terminal ~19km from Perth CBD ~30 minutes Most departures operate from here; large adjacent parking facilities
Hillary’s Boat Harbour ~24km north of Perth CBD ~25 minutes Northern suburbs departure point; useful if staying north of Perth

Your hire car can be driven to the ferry terminal of your choice and parked in the designated car parks while you are on the island.

Getting Around Rottnest Island

Once on the island, the primary transport options for visitors are:

  • Bicycle hire: cycling is the classic Rottnest experience and the best way to reach the beaches and bays scattered around the island. Bike hire is available from multiple operators on the island. Book in advance during school holidays and peak periods
  • Island Explorer bus: a hop-on hop-off bus service connects the main settlement with the beaches and attractions around the island. A day pass is available and suits visitors who prefer not to cycle
  • Organised tours: guided tours by bus and electric cart cover the island’s history, wildlife, and geography. Rottnest Island operates its own guided tours from the main visitor hub
  • Walking: the settlement area and some nearby beaches are accessible on foot. The island is larger than it appears, and walking to the outer beaches is a full-day commitment

Spotting Quokkas

Rottnest Island is one of the only places in the world where quokkas can be easily observed in their natural habitat. These small, friendly marsupials are found throughout the island and are particularly concentrated around the main settlement. They are wild animals and should not be fed, but they are accustomed to human presence and are a highlight of most Rottnest visits.

💡  Book your ferry in advance, especially for weekend and school holiday visits: Rottnest Island ferries, particularly the fast-ferry services from Fremantle, book out well in advance during peak periods. Book your ferry tickets before you book anything else, and then plan your hire car dates around the ferry departure and return schedule.

Frequently Asked Questions

Is there parking at the Fremantle ferry terminal?

Yes. The Fremantle Passenger Terminal has commercial car parking facilities nearby. Parking at the terminal costs more than parking further from the waterfront and walking, so if you plan to leave your hire car for a full day or overnight, consider the parking options in the wider Fremantle area versus parking at the terminal directly.

Can I do Rottnest Island as a day trip?

Yes, day trips to Rottnest are the most common format. The fast ferry from Fremantle takes approximately 30 minutes. A day trip allows six to eight hours on the island, which is enough to cycle the main circuit, visit two or three beaches, and see the quokkas in the settlement. An overnight stay opens up more of the island. Burswood Car Rentals’ flexible hire options make it easy to match your hire period to your Rottnest itinerary.

Perth to Fremantle by Car: What to See Along the Way

Fremantle is one of Perth’s most visited destinations and one of the easiest by hire car. Just 19 kilometres south of the Perth CBD, the drive takes approximately 30 minutes in normal traffic, though there is no shortage of worthwhile stops that can stretch the journey into a half-day or full-day experience. Whether you are a first-time visitor to Western Australia or a Perth local exploring your own backyard, the Perth to Fremantle drive rewards a leisurely approach.

Burswood Car Rentals is conveniently located near Perth Airport and has been serving Perth visitors and locals for over 42 years. Hire a car from Burswood to explore Fremantle and the coast at your own pace.

Explore Perth and Fremantle at Your Own Pace

Burswood Car Rentals: from $25/day, no hidden fees, RAC roadside assistance. Call (08) 9362 4777.

Get a Quote

Route Options: Direct or Scenic

There are two main route options for the Perth to Fremantle drive, each with a different character:

  • Stirling Highway (via Cottesloe and Mosman Park): the most scenic coastal route. Stirling Highway runs south through the leafy western suburbs, passing close to the coast and through the beach suburbs of Claremont and Cottesloe before arriving in Fremantle. This is the recommended option for first-time visitors as it passes through some of Perth’s most attractive suburbs
  • Canning Highway (via South Perth and Applecross): a riverside route that follows the Swan River south before crossing to Fremantle. This route passes through the Applecross foreshore area, which has river views and a good cafe strip

What to See on the Way

Cottesloe Beach

Cottesloe is Perth’s most iconic beach and is just off the Stirling Highway route. A well-maintained foreshore with Norfolk Island pines, a heritage beach pavilion (the Indiana Tea House), ocean swimming, and weekend markets make Cottesloe worth a 30 to 60 minute stop. It is family-friendly, has good facilities, and is one of the most photographed beach locations in Western Australia.

Mosman Park and Peppermint Grove

The drive through Mosman Park and Peppermint Grove on Stirling Highway passes through some of Perth’s most established and affluent residential streets, with large heritage homes and significant streetscapes. It is a pleasant drive in itself even if you do not stop.

North Fremantle

North Fremantle, just before you cross the Swan River into central Fremantle, has a good cafe and restaurant strip along the waterfront. The area has a more local character than the tourist-facing parts of Fremantle and is worth considering for a coffee stop.

What to Do in Fremantle

  • Fremantle Market: the historic Fremantle Market at South Terrace operates on Friday afternoons and over weekends, offering fresh produce, crafts, clothing, and food stalls in a heritage market building
  • The Cappuccino Strip: South Terrace is Fremantle’s main cafe and restaurant street, known locally as the Cappuccino Strip. It has been the social heart of Fremantle for decades and remains a great spot for coffee and people-watching
  • Fremantle Prison: a UNESCO World Heritage Site and one of the most intact colonial-era prisons in the world. Guided tours, night tours, and tunnel tours operate daily and are well worth booking in advance
  • Fishing Boat Harbour: the working fishing harbour and adjacent restaurant strip is the best place in Perth for fresh fish and chips eaten waterside
  • WA Maritime Museum: the Western Australian Maritime Museum houses the winning yacht from the 1983 America’s Cup (Australia II) along with extensive maritime history displays. Free entry for the main museum
  • Fremantle Arts Centre: a beautiful heritage building (former lunatic asylum) now operating as an arts venue and gallery, with a courtyard cafe
✦  Parking in Fremantle: Fremantle has a mix of paid street parking, free timed street parking in some areas, and paid parking stations. The Kings Square area and the Fremantle Railway Station precinct have the highest concentration of parking. On market days (Fridays and weekends), parking fills quickly around the South Terrace area. Arriving before 10am on a weekend secures much better parking options.

Frequently Asked Questions

How long should I plan for a Perth to Fremantle day trip?

A morning departure from Perth with stops along the way and several hours in Fremantle makes for a comfortable full-day experience. If you add Cottesloe Beach as a swim stop, a Fremantle Prison tour, the market, and lunch at the Fishing Boat Harbour, five to six hours in the Fremantle area alone is not excessive.

Is Fremantle easy to navigate by car?

Fremantle is compact and easy to navigate. The main tourist areas are concentrated within a few streets of each other. Parking at one location and exploring on foot is the most practical approach. Burswood Car Rentals’ hire cars have no rental stickers, so you arrive without advertising that you are in a rental vehicle.

Perth to the Pinnacles by Hire Car: Everything You Need to Know

The Pinnacles Desert is one of Western Australia’s most extraordinary natural attractions. Thousands of ancient limestone pillars rising from golden sand in Nambung National Park create a landscape that looks unlike anywhere else on earth. It makes for one of the best day trips or overnight getaways from Perth, and the drive up the coast to reach it is worth the journey in its own right.

This guide covers everything you need to plan your Pinnacles trip by hire car from Perth. Burswood Car Rentals has been helping Perth visitors and locals get on the road for over 42 years, with no hidden fees and RAC roadside assistance included on every rental.

Hire a Car from Burswood Car Rentals for Your Pinnacles Day Trip

From $25/day. No hidden fees. RAC roadside assistance. Near Perth Airport. Call (08) 9362 4777.

Get a Quote

The Drive: Distance and Time

The Pinnacles are located in Nambung National Park, approximately 245 kilometres north of Perth. The most direct route is via the Brand Highway (Indian Ocean Drive is the more scenic alternative along the coast, adding around 30 to 40 minutes to the journey). Driving time from Perth is approximately 2.5 to 3 hours each way without stops.

Route Distance Drive time Character
Brand Highway (direct) ~245km ~2.5 hours Inland route, more direct, quicker
Indian Ocean Drive (coastal) ~270km ~3 to 3.5 hours Scenic coastal route, passes Lancelin, recommended for the return leg

What to Do at the Pinnacles

Pinnacles Lookout Drive

A 4-kilometre one-way sealed loop road winds through the heart of the Pinnacles formation, allowing you to drive slowly through the limestone pillars and stop at designated pull-off areas for photographs. The loop takes about 45 minutes to an hour if you stop frequently. This is the main Pinnacles experience and it is accessible to all hire car types, including standard sedans.

Walking trails

There is a short walking trail through the Pinnacles formation that allows you to get closer to the limestone pillars than the road allows. The trail is flat and takes approximately 30 minutes at a relaxed pace. Sturdy footwear is recommended.

Pinnacles Desert Discovery Centre

The visitor centre at the entrance to the Pinnacles includes displays on the geological formation of the limestone pillars, the history of the area, and local wildlife. Entry to the centre is free with your park pass.

Entry Fees and Park Passes

Nambung National Park is a Western Australian national park and requires a park entry fee per vehicle. A standard day pass can be purchased at the park entry gate (card payment accepted) or in advance through the Parks and Wildlife Service of Western Australia (parks.dpaw.wa.gov.au). A WA Holiday Parks Pass or annual pass provides entry to all WA national parks for 12 months and represents good value if you plan to visit multiple parks during your trip.

The Town of Cervantes: Where to Stop

The small coastal town of Cervantes is approximately 3 kilometres from the Pinnacles entrance and is the best base for refreshments, fuel, and a short stop. Cervantes has:

  • Fuel stations and a small supermarket for supplies
  • Several cafes and restaurants including seafood options featuring local rock lobster
  • The Lobster Shack: a popular attraction offering tours of a working rock lobster processing facility and a restaurant with local lobster meals; bookings recommended during school holidays and peak season

What to See on the Way: Lancelin

If you take the Indian Ocean Drive route on the return trip, Lancelin is worth a stop. Located approximately 130km north of Perth, Lancelin is known for its white sand dunes that extend inland from the coast. The dunes are accessible from the town and are popular with sandboarders. It is a good mid-trip break on the return journey.

💡  Visit early morning or late afternoon: The Pinnacles are at their most photogenic and most comfortable early in the morning (before 10am) or in the late afternoon (after 4pm). Midday visits in summer can be very hot, and the light is harsh for photography. Early visits also mean fewer fellow travellers in your photos. If you plan a day trip, leaving Perth by 7am puts you at the Pinnacles in the best morning light.

Frequently Asked Questions

Can a standard hire car do the Pinnacles loop drive?

Yes. The Pinnacles Lookout Drive is a sealed road and is suitable for any standard hire car. A four-wheel-drive vehicle is not required for the Pinnacles experience. All vehicles in the Burswood Car Rentals fleet are suitable for the Pinnacles day trip on the sealed road.

Is it worth staying overnight in Cervantes?

If you want to catch the early morning light at the Pinnacles without the 2.5-hour pre-dawn drive from Perth, staying overnight in Cervantes puts you right at the gate at opening time. Cervantes has accommodation options including caravan parks and holiday units. Staying overnight also gives you time for a late afternoon visit on the first day and an early morning visit the following day, which is the ideal way to experience the Pinnacles. Burswood Car Rentals offers flexible hire periods to suit both day trips and multi-day itineraries.

Is there fuel available at the Pinnacles?

There is no fuel available inside Nambung National Park. Cervantes, 3km from the park entrance, has a fuel station. Fill up before leaving Perth or at Lancelin on the way up, and top up in Cervantes before the return journey.

How to Navigate Perth Without Getting Lost in a Hire Car

navigate Perth hire car without getting lost Burswood

Perth looks straightforward on a map. A coastal strip, a river bisecting the southern suburbs, a CBD grid, and a network of arterial roads heading north, south, and east. But like any large city, Perth has its quirks: roads that seem to double back on themselves near the river, a CBD that requires a bit of thought around one-way streets and free transit zones, a freeway system that still catches newcomers off guard, and a scale that surprises visitors who do not appreciate how spread-out a city of this size becomes.

Burswood Car Rentals has been helping visitors and locals navigate Perth from our base at 16 Teddington Road, Burswood for over 42 years. Here is the local knowledge guide: what you need to know about Perth’s roads before you get in the driver’s seat.

Use a Navigation App, Not Printed Maps

The single most important navigation decision you make before driving a hire car in Perth is to use a live, GPS-based navigation application on your phone. Google Maps and Apple Maps both work well in Perth and WA. Waze is popular for city driving. All three update in real-time for traffic conditions, which matters in Perth’s peak-hour freeway merges.

Before you drive, set up your navigation for the first journey while the car is parked. Enter your destination, review the route, and start the audio navigation. Do not try to read a map on your phone while driving: it is illegal and unsafe. A phone mount on the windscreen or dashboard keeps your navigation visible without requiring you to pick up your phone.

Understanding Perth’s Freeway System

Perth’s freeway network is the main structural element of its road system. Understanding the key freeways makes most navigation decisions much simpler:

  • Mitchell Freeway (north/south in the northern corridor): runs from the Narrows interchange near the CBD northward through Joondalup and beyond. If you are heading to Scarborough, Hillarys Boat Harbour, Joondalup, or anywhere in Perth’s north, the Mitchell Freeway is likely your primary route
  • Kwinana Freeway (south): runs from the Narrows southward through Fremantle direction, Cockburn, and toward Rockingham and Mandurah. Also provides access to Fremantle via the Stock Road turnoff. If you are going south of the river, the Kwinana Freeway is your main arterial
  • Graham Farmer Freeway (east-west link): runs through a tunnel under Northbridge, connecting the Mitchell Freeway north of the CBD to the Eastern Freeway. Useful for bypassing the CBD when moving between north and east Perth
  • Great Eastern Highway: the main road heading east toward the Perth Hills, Mundaring, York, and beyond into the Wheatbelt
  • Tonkin Highway and Roe Highway: the eastern bypass route connecting the southern and northern suburbs without entering the CBD or using the coastal freeways

Driving in Perth’s CBD

Perth’s city centre has several features that catch out unfamiliar drivers:

One-way streets

Parts of Perth’s CBD grid run on one-way systems. Hay Street and Murray Street in the mall area, and sections of St Georges Terrace and Adelaide Terrace, operate differently to what navigation apps sometimes show on their first suggestion. Trust your navigation app over any instinct: it knows the one-way system.

Free Transit Zone parking restrictions

Perth CBD has a Free Transit Zone (FTZ) for public transport, but driving and parking within the CBD is separate from this. Parking in the CBD requires paid parking at meters or in commercial car parks. Council parking regulations in the inner city are actively enforced. For multi-hour CBD visits, using an off-street car park (Convention Centre car park, Wilson Parking on Roe Street, and others) is simpler than hunting for meter parking.

The Causeway and the Narrows

Crossing the Swan River between the north and south sides of Perth requires either the Causeway (connecting East Perth to Victoria Park) or the Narrows Interchange (the main freeway connection near the CBD). Both are clearly signed. The Narrows is the faster option for freeway travel; the Causeway is useful for accessing East Perth and Burswood from the south. Burswood Car Rentals is located right at the Burswood interchange, making it very easy to reach from both directions.

Key Routes Worth Knowing

Destination Recommended route Notes
Perth Airport from city Orrong Rd or Great Eastern Hwy east Follow airport signs from Great Eastern Hwy
Fremantle from city Kwinana Fwy south to Stirling Hwy Or Stirling Hwy direct; 20-25 min
Cottesloe or City Beach West via Hay St then Stirling Hwy Stirling Hwy runs along the coast
Scarborough Beach Mitchell Fwy north, West Coast Hwy exit 30 min from city in light traffic
Swan Valley Great Eastern Hwy or Midland and north Midland Gate is the gateway suburb
Hills and Kalamunda Great Eastern Hwy east to Zig Zag Winding roads in the Hills; take it easy
Margaret River (280 km) Kwinana Fwy south to South West Hwy Allow 3 to 3.5 hours

 

Perth Driving Habits to Know About

Local knowledge goes beyond knowing the roads. Here are a few Perth-specific driving habits that help newcomers blend in and stay safe:

  • Merging at freeway on-ramps: Perth’s freeways use zip-merge (alternate merge) at on-ramps. Do not stop at the top of an on-ramp: accelerate to match freeway speed and merge when a gap appears
  • Right turns at traffic lights: unless there is a dedicated right-turn arrow, you may be required to wait for a gap in oncoming traffic before turning right. Do not block the intersection while waiting
  • School zones: 40 km/h speed zones operate around schools on weekday mornings and afternoons when the zone lights are flashing. These are heavily policed and the reduced limit genuinely applies even when the streets appear quiet
  • Cyclists: Perth has an expanding network of dedicated cycling infrastructure, but cyclists are also present on many roads. Give cyclists at least one metre of clearance when overtaking (1.5 metres on roads above 60 km/h)
  • Kangaroos at dusk and dawn: on regional roads outside the metropolitan area, particularly on routes heading toward the Wheatbelt, South West, or north of the city, kangaroos are a genuine road hazard at dawn and dusk. Slow down and stay alert on country roads in low-light conditions

With a good navigation app, a well-maintained hire car from Burswood Car Rentals, and the local knowledge in this guide, Perth’s roads are straightforward and the rewards of getting out and exploring are enormous. Whether you are heading to Fremantle, the Hills, Margaret River, or simply getting around the city, Western Australia is best experienced from behind the wheel.

Frequently Asked Questions

Are Perth roads easy to drive for visitors?

Generally yes. Perth’s roads are well-maintained, clearly signed, and less congested than Sydney or Melbourne. The main adjustments for visitors are driving on the left, understanding the freeway merge system, and watching out for speed cameras, which operate throughout the metropolitan area and on country roads. The Burswood FAQs page has more practical answers for first-time Perth visitors.

Is there a toll system in Perth?

Perth does not have a toll road network. There are no tolls on the Kwinana Freeway, Mitchell Freeway, or other metropolitan roads. You can drive anywhere in the Perth metropolitan area without toll charges, which is a practical advantage compared to Sydney and Melbourne.

What size hire car is best for driving in Perth?

For solo travellers and couples, a compact car or mid-size sedan is easy to park and navigate in Perth’s CBD and inner suburbs. For families or groups, the 8-seater Kia Carnival people mover handles Perth’s wider roads and regional highways comfortably. For a premium experience, Burswood’s Audi luxury range delivers exceptional comfort across both city and regional driving.

Car Hire in Perth for International Visitors: Everything You Need to Know

car hire Perth international visitors guide Burswood Car Rentals

Perth is one of the world’s most driveable cities for international visitors. The roads are wide, the traffic is manageable by major city standards, the scenery is stunning, and within an hour of the city centre you can be in some of the most beautiful landscape on earth. The hire car is how most international visitors get the best out of WA, and getting the paperwork right before you pick up the keys makes the whole experience significantly smoother.

Burswood Car Rentals has been welcoming international visitors to Perth for over 42 years. We are conveniently located on the route from both the domestic and international airports, and our local team speaks from real experience when guiding overseas visitors through the hire process. Here is everything you need to know.

Driving Licence Requirements for International Visitors

Your ability to drive legally in Western Australia depends on the country that issued your licence and whether it is written in English.

  • Licences issued in English: a valid overseas driving licence that is written in English may be used in Western Australia. Carry your licence at all times while driving
  • Licences not issued in English: if your overseas licence is not in English, you will generally also need an International Driving Permit (IDP) to drive legally in WA. The IDP is a translation document issued by the motoring authority in your home country, and must be carried alongside your original home-country licence
  • Your IDP cannot be used alone: an IDP is a translation document. It is not valid without the original licence it translates. Always carry both

Specific requirements, including any time limitations on using an overseas licence, are set by the Road Traffic Administration Act and related regulations in Western Australia. Please verify current requirements with Main Roads WA at mainroads.wa.gov.au before your trip. Requirements can change.

The First Rule of Driving in Australia: Keep Left

If you are visiting from a country that drives on the right (which includes the USA, most of Europe, China, and many other nations), the single most important adjustment to make is driving on the left side of the road.

This sounds straightforward until you are tired from a long-haul flight, it is your first time in an unfamiliar hire car, and you are making a right turn at a busy Perth intersection. Here is how to set yourself up for success:

  • At every intersection, consciously remind yourself to keep to the left as you exit the turn
  • At a roundabout, traffic flows clockwise: give way to vehicles already in the roundabout, entering from your right
  • The driver sits on the right side of the car in Australia: if you feel like you are in the wrong seat, you are in the right one
  • Be particularly careful when departing from quiet car parks or after a rest stop, as these are common moments for left-right disorientation
  • Give yourself an easy first drive: do not leave the airport at peak hour heading directly into the CBD. A short, quiet route on your first drive helps the left-side habit settle in

Key Road Rules for International Visitors to WA

Western Australia’s road rules are based on the Australian Road Rules, which apply across the country with minor state variations. The following are the most important for international visitors to understand:

  • Speed limits: 50 km/h in built-up residential areas, 40 km/h in school zones when active, 60 km/h on most urban arterial roads, 80 or 100 km/h on suburban freeways, and 110 km/h on open highways. Speed cameras operate extensively across WA and fines are substantial
  • Seatbelts: mandatory for all occupants in all seating positions. The driver is responsible for ensuring all passengers under 16 are properly restrained
  • Mobile phones: it is illegal to hold or use a mobile phone while driving in WA. Hands-free systems are permitted. Even brief phone handling at traffic lights is an offence. Use your phone before you start driving or invest in a car mount for navigation
  • Blood alcohol limit: 0.05 for most licence holders. Zero for learner and probationary licence holders. Western Australian police conduct roadside breath testing. The penalties are severe. Do not drink and drive
  • Give way to pedestrians: at marked pedestrian crossings, pedestrians have right of way. At intersections, give way to pedestrians crossing the road you are turning into
  • Bicycle lanes: do not drive in bicycle lanes. Some bicycle lanes in Perth allow car access only at specific times and for specific purposes

What to Bring When Hiring a Car in Perth

When you arrive at Burswood Car Rentals to pick up your vehicle, bring:

  1. Your original overseas driving licence
  2. Your International Driving Permit (if your licence is not in English)
  3. Your passport
  4. The credit or debit card you will be paying with (the same card used for the booking)
  5. Your booking confirmation if you have one

If you have any questions before you arrive, the Burswood FAQs page covers many common hire questions, or you can call the team directly on +61 8 9362 4777.

Perth Distances and What Vehicle to Choose

Understanding Perth’s geography helps you choose the right vehicle for your trip:

Destination Distance from Perth CBD Vehicle recommendation
Fremantle About 20 km south-west Any vehicle in the fleet
Swan Valley About 25 km north-east Compact or mid-size sedan
Rottnest Island Ferry from Fremantle Ferry only; leave the hire car in Fremantle
Margaret River About 280 km south Sedan or SUV; comfortable for the drive
Albany About 420 km south-east Sedan or SUV; allow a full day’s driving
Kalbarri About 590 km north SUV recommended for longer trip comfort
Groups or families Varies 8-seater Kia Carnival people mover

For families or groups, Burswood’s 8-seater Kia Carnival makes large-group travel comfortable and economical compared to two separate vehicles. For a premium Perth experience, our Audi luxury vehicles deliver a driving experience that matches Perth’s world-class attractions.

Frequently Asked Questions

Can I hire a car in Perth if I am under 25?

Burswood Car Rentals has minimum age requirements for hire vehicles. Check the FAQs page or contact the team directly to confirm the current minimum age requirements and any applicable young driver policies. The minimum age varies by vehicle type.

Can I pick up my hire car from Perth Airport?

Burswood Car Rentals is located at 16 Teddington Road, Burswood, on the route from both Perth’s domestic and international airports to the CBD. We offer free pickup from Perth hotels in the city. Contact the team to arrange airport or hotel pickup for your hire vehicle.

What is the nil damage excess policy?

Burswood Car Rentals offers a nil damage excess policy, which means you are not required to pay an excess in the event of accidental damage during your hire period. This is particularly valuable for international visitors who may not have suitable travel insurance cover for hire car excess. Review the full terms or ask the team to explain the policy clearly at pickup.

Eco-Friendly Car Hire in Perth: How to Reduce Your Carbon Footprint

eco-friendly car hire Perth reduce carbon footprint Burswood

Travelling responsibly does not mean giving up the freedom and flexibility of a hire car. It means making thoughtful choices about which vehicle you hire, how you drive it, and how you plan your trip. For visitors and locals in Perth, there are genuinely meaningful ways to reduce the environmental impact of your hire car travel without compromising on where you go or how comfortable you are getting there.

Burswood Car Rentals has been a Quality Tourism Accredited Perth car hire company for over 42 years. As Perth’s transport landscape shifts toward lower-emission vehicles, we are shifting with it. Here is the practical guide to eco-friendly car hire in Perth.

Step 1: Choose the Most Fuel-Efficient Vehicle for Your Trip

The single biggest factor in the environmental footprint of your hire car trip is the vehicle you choose. A smaller, more fuel-efficient car produces meaningfully less CO2 per kilometre than a large SUV or ute, regardless of how eco-consciously you drive.

Burswood’s practical guide to vehicle choice by trip type:

  • Solo travel or couple in Perth: a compact car like the Kia Rio or similar economy option is the lowest-emission choice in the conventional fleet and is perfectly adequate for Perth CBD and inner suburb travel
  • Family or small group: a mid-size sedan or small SUV uses fuel more efficiently than an 8-seater if you don’t genuinely need the extra seats. Hire the right size, not the largest available
  • Any trip where charging is viable: the CUPRA Tavascan produces zero tailpipe emissions. For Perth city and short regional trips where the charging network supports the route, the electric option is the most environmentally responsible choice available

Step 2: Consider the Electric Vehicle Option

Burswood Car Rentals is currently trialling the CUPRA Tavascan, a premium electric SUV that produces zero tailpipe emissions. For a visitor to Perth whose itinerary includes the city, Fremantle, the Swan Valley, and possibly Margaret River, the Tavascan covers the journey without burning a single litre of petrol.

The environmental argument for an EV hire in Perth is straightforward. A week of city and regional driving in a petrol vehicle produces a substantial CO2 output. The same trip in the CUPRA Tavascan produces no direct tailpipe emissions. The full lifecycle carbon comparison between EVs and petrol vehicles is more complex (manufacturing, battery production, and the grid mix all factor in), but for the in-use travel emissions that most travellers think about, an EV hire is the clear environmental choice.

Step 3: Drive More Efficiently

Once you have the right vehicle, how you drive it has a significant effect on fuel consumption and emissions. These habits apply equally to petrol and EV hire cars (for EVs, they extend range and reduce overall energy use):

  • Smooth acceleration and braking: rapid acceleration burns significantly more fuel than gradual acceleration to cruising speed. Anticipate the road ahead, accelerate gently, and let the car coast before braking where safe and legal to do so
  • Maintain a steady speed on highways: fuel consumption increases sharply above 100 km/h on Western Australian highways. Keeping to the posted speed limit is both the legal and the more fuel-efficient choice
  • Use air conditioning strategically: air conditioning adds fuel consumption. In mild Perth weather, opening windows is more efficient. In summer heat, air conditioning at moderate settings is more efficient than open windows at highway speeds
  • Avoid unnecessary idling: turning off the engine at extended stops of more than a minute or two reduces fuel consumption and emissions
  • Check tyre pressure before longer trips: underinflated tyres increase rolling resistance and fuel consumption. The Burswood team maintains vehicles in good condition, but it is worth a quick check before heading out on a longer regional drive

Step 4: Plan Your Route to Minimise Distance

The greenest kilometre is the one you do not drive. Perth is a large, spread-out city, and route planning genuinely affects total distance travelled:

  • Use a navigation app with live traffic data to avoid congestion, which dramatically increases fuel consumption
  • Cluster activities by area on each day of your trip rather than crisscrossing the city
  • For shorter distances in central Perth, consider using public transport (the free CAT buses in the city centre, or the train network to Fremantle) and using the hire car for the trips that genuinely require one
  • When driving in the Perth Hills, Margaret River region, or other scenic areas, plan a circuit route rather than an out-and-back where possible

Step 5: Offset What You Cannot Avoid

For the emissions you cannot eliminate, consider a carbon offset. Several Australian organisations offer verified carbon offset programmes. A two-week hire car trip in WA can be offset for a relatively modest cost. Look for offset programmes that are independently verified against recognised standards (such as the Australian National Carbon Offset Standard or Gold Standard accreditation).

A Note on Vehicle Returns and Fleet Efficiency

Burswood Car Rentals maintains its fleet to a high standard, with regular servicing that keeps vehicles operating at their rated fuel efficiency. The no-hidden-fees, nil damage excess policy means there are no incentives for customers to hide vehicle issues that might affect performance, which helps us keep the fleet in optimal condition for both efficiency and safety.

Frequently Asked Questions

Is hiring an electric car in Perth more expensive than a petrol car?

The daily hire rate for the CUPRA Tavascan is higher than our economy and standard petrol vehicles, reflecting its premium positioning. However, the lower cost of charging versus petrol partially offsets the rate difference, particularly on longer hire periods. For customers for whom the environmental benefit or the premium driving experience has value, the Tavascan represents good value on both dimensions. Contact us for current pricing.

Which car in the Burswood fleet has the lowest emissions for a short Perth city trip?

For a short Perth city trip, the CUPRA Tavascan has zero tailpipe emissions and is the clear lowest-emission choice where the route is viable. For those who prefer a petrol vehicle, our economy and compact options have the lowest fuel consumption per kilometre in the conventional fleet.

Electric and Hybrid Hire Cars in Perth: Are They Worth It?

electric hybrid hire car Perth worth it Burswood Car Rentals

Perth has changed. A city that was once almost entirely reliant on the car and the petrol bowser now has a growing network of EV charging infrastructure, a new generation of genuinely impressive electric vehicles on the road, and hire car customers asking a question that barely existed five years ago: should I hire an electric car?

Burswood Car Rentals has been on Perth’s roads for over 42 years and has recently added the CUPRA Tavascan to the fleet as part of our commitment to giving customers modern transport options. Whether an electric hire car is right for your Perth trip depends on where you are going, how far you are travelling, and what kind of driving experience you are looking for. Here is the honest guide.

What Is Available for Electric Hire in Perth?

Burswood Car Rentals is currently trialling electric vehicle hire in Perth with the CUPRA Tavascan, a premium electric SUV from the SEAT/Volkswagen Group’s CUPRA brand. The Tavascan is not a budget compact: it is a proper, striking SUV with European design, instant acceleration, a quiet and refined cabin, and the kind of technology package you would expect from a premium vehicle.

The CUPRA Tavascan delivers an experience that is genuinely different to a conventional petrol car. The acceleration is immediate and smooth. There is no engine noise, which gives the cabin a calm, quiet quality that is particularly noticeable on long highway stretches. And at a time when Perth petrol prices remain a talking point for everyone from commuters to tourists, the running costs of an EV tell their own story.

What Are the Advantages of Hiring an Electric Car in Perth?

  • Running cost savings: charging an electric vehicle costs significantly less per kilometre than fuelling a petrol car at Perth pump prices. For a week-long hire in an EV, the difference between charging costs and petrol costs represents a genuine saving, particularly on longer drives
  • Zero tailpipe emissions: for travellers who want to reduce the environmental impact of their visit to Western Australia, an EV hire produces no direct tailpipe emissions
  • The driving experience: instant torque, smooth acceleration, and a quiet cabin are features that experienced EV drivers consistently describe as something you can’t appreciate until you have driven one. The CUPRA Tavascan in particular delivers genuine driving pleasure alongside its efficiency
  • Technology and comfort: the Tavascan comes with advanced driver assistance technology, a premium interior, and cutting-edge infotainment, making it a compelling option for business travellers and anyone who values a premium-quality hire experience
  • City driving efficiency: EVs are particularly well suited to city driving because the regenerative braking system recovers energy during deceleration. Perth’s stop-start CBD and inner suburb driving is well matched to an EV’s strengths

What Are the Limitations to Consider?

An honest guide to EV hire would be incomplete without addressing the genuine limitations. These are not reasons to avoid an electric hire car, but they are factors to plan around.

  • Range planning: the CUPRA Tavascan has a strong range per charge, but any EV hire in Western Australia requires some route planning if you are heading into regional areas. Perth to Margaret River is an entirely manageable trip in the Tavascan. Perth to Kalbarri or Albany in a single day without advance charging planning requires more consideration
  • Charging time vs refuelling time: topping up a petrol car takes four minutes. An EV rapid charge takes 20 to 45 minutes depending on the charger and the state of charge. For some itineraries, this does not matter at all. For others, it requires scheduling a charging stop into the day
  • Charging network familiarity: first-time EV drivers sometimes find navigating the charging network slightly unfamiliar. Burswood Car Rentals provides a guide to Perth and WA charging options when you hire the Tavascan, and the car’s navigation system will route you to chargers along your journey

Perth’s EV Charging Landscape

Perth’s public charging network has expanded considerably in recent years, driven by state government investment and commercial deployment. Key charging points relevant to Burswood Car Rentals hire customers include:

  • Fast DC chargers in Perth CBD and major shopping precincts including Karrinyup, Innaloo, and Midland Gate
  • Rapid charging on the Kwinana Freeway corridor heading south toward Fremantle and Rockingham
  • Charging at selected service stations on the South West Highway heading toward Bunbury and Margaret River
  • Charging infrastructure at major regional centres including Bunbury and Busselton

The Tavascan’s built-in navigation uses real-time charging point data to plan routes and identify available chargers, which removes much of the guesswork from charge planning.

Is an Electric Hire Car Worth It for Your Perth Trip?

Trip type EV suitability Notes
Perth CBD and inner suburbs Excellent City stop-start driving plays to EV strengths. No range concerns.
Perth to Fremantle Excellent Short trip, easy charging options. Highly recommended.
Perth to Margaret River Very good Charging available en route and in the region. Plan one stop.
Perth to Swan Valley Excellent Short round trip well within single charge.
Perth to Albany or Esperance Moderate Possible with advance planning; requires charging stop at Bunbury or further.
Perth to Kalbarri or Exmouth Not recommended Charging infrastructure thins significantly beyond Geraldton.

For the majority of Perth tourist itineraries and business travel needs, the CUPRA Tavascan is not only a viable choice: it is arguably the most enjoyable hire car we have. Contact the Burswood team to check availability and discuss whether the Tavascan suits your planned route.

Frequently Asked Questions

Do I need special knowledge to drive a hire EV?

No. The CUPRA Tavascan drives like a conventional automatic car with one significant difference: there is no gear selection beyond Drive, Reverse, and Park. The accelerator and brake pedals work the same way. The main adjustment for first-time EV drivers is getting used to regenerative braking (a mild resistance when you release the accelerator) and remembering to plug in at charging stops. Burswood’s team walks you through all the key functions when you pick up the vehicle.

Is the CUPRA Tavascan available at the airport?

Burswood Car Rentals is located at 16 Teddington Road, Burswood, on the route from Perth’s domestic and international airports to the CBD. We offer free pickup and delivery to Perth CBD hotels. Contact us to discuss airport pickup arrangements for the CUPRA Tavascan.

How much does it cost to charge the CUPRA Tavascan?

Public charging costs in Perth vary between providers and tariff types. Fast chargers at shopping centres typically charge by the minute or by the kilowatt-hour. For a full charge from near-flat, a rough comparison to petrol costs consistently shows EV charging to be significantly cheaper per kilometre at current Perth petrol prices. Exact charging costs depend on which network and tariff you use during your hire period.